DB PM 1000 Operations Instructions

Operating Instructions and Parts Manual 10-inch Cabinet Saw Model PM1000  Powermatic 427 New Sanford Road LaVergne, Tennessee 37086 Part N

107.0 Setup and assembly 7.1 Shipping contents 7.1.1 Carton contents (Figure 1) 1 Cabinet saw 1 Guard assembly (A) 1 Miter gauge (B) 1 A

111. Remove screws holding saw to pallet, by unscrewing them from underneath pallet. 2. Carefully slide saw from pallet onto floor. The cabinet saw

121. Shift extension wing so it is slightly above saw table surface. 2. Begin by tightening the three screws (17mm wrench) under the extension wing

13Figure 9 NOTE: If while lowering blade, the points on the anti-kickback pawls tend to catch in the seam between table and table insert, slightly ra

146. Riving knife must be parallel to saw blade. See section 9.6 for inspection and adjustments. NOTE: A low-profile riving knife is also provided,

152. Grounded, cord-connected tools intended for use on a supply circuit having a nominal rating less than 150 volts: This tool is intended for use o

16 Do not rely that no light means no power to the machine. Always check for power first. Failure to comply may cause serious injury. To start saw, p

179.4.3 Extension plate The extension plate (D, Figure 17) can be adjusted by sliding to the right or left or removed entirely. To adjust, loosen t

18 Figure 21 9.5.2 Tilt stop 45° Repeat steps 1 through 4 above for 45° setting, as shown in Figure 22. Loosen nut (B1) with 11mm wrench, and turn s

199.6.2 Blade proximity alignment The gap between saw blade and riving knife must be between 3 and 8mm (Figure 26). Figure 26 If adjustment is need

21.0 Warranty and Service Powermatic warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, pl

203. Press down on motor while retightening screw (C). If belt shows signs of wear, fraying, cracks, etc. it should be replaced, as follows. 9.8.2 B

21accidents. Never use a cracked saw blade. The use of a sharp, well maintained, and correct cutting tool for the operation will help avoid injuries.

22 Figure 33 Figure 34 When ripping long boards, use a support at front of table (C, Figure 34), such as a roller stand, and a support or "tail

23Length stops should not be used on the free end of the workpiece in the cutoff area. Do not crosscut workpieces shorter than 6". Before starti

24 Figure 41 The process of cutting 1/8" to 13/16" grooves in workpieces is accomplished by the use of a stacked dado blade set or an adjus

25Push stick and push block The use of a push block or push stick provides an added level of safety for the operator. A push stick is included with y

2612.0 Maintenance Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injur

2713.0 Optional accessories These accessory items (purchased separately) can enhance the functionality of your table saw. Contact your dealer to ord

2814.0 Troubleshooting the PM1000 Cabinet Saw Table 2 Symptom Probable Cause RemedySaw will not start. No incoming power. Check plug connection. Lo

29Symptom Probable Cause RemedyExcessive vibration. Tilting or raising lock knobs not tightened. Tighten lock knobs on handwheels Machine not restin

32.0 Table of contents Section Page 1.0 Warranty and Service ...

3015.1.1 PM1000 Table and Cabinet Assembly – Exploded View  323131A(optional)30333435362427282923252637383839404243454543464628482848495052475354

3115.1.2 PM1000 Table and Cabinet Assembly – Parts List Index No Part No Description Size Qty 1 ... 1791789 ... Mi

32Index No. Part No. Description Size Qty 59 ... PM1000-059... Tilt Angle Scale ...

3315.2.1 PM1000 Motor and Trunnion Assembly – Exploded View  1011021041051061081061071091101111111181131141051121161151201241251261281291091281

3415.2.2 PM1000 Motor and Trunnion Assembly – Parts List Index No Part No Description Size Qty 101 ... PM1000-101... Arbor N

35Index No. Part No. Description Size Qty 151 ... PM1000-151... Tilting Shaft ...

3615.3.1 PM1000 Blade Guard Assembly – Exploded View 132455678910111112131314151516171616161817201919191921232224725261717271A1B

3715.3.2 PM1000 Blade Guard Assembly – Parts List Index No Part No Description Size Qty 1 ... PM1000-301... Riving Kni

3816.0 Electrical Connections for PM1000 ELECTRICAL SCHEMATIC - 115V70uf / 250 VAC300MFD / 125 VACELECTRICAL SCHEMATIC - 230V70uf / 250 VAC300MFD

39This page intentionally left blank. 

3.0 Safety warnings 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings

40 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.powermatic.com

525. Maintain tools with care. Keep blade sharp and clean for the best and safest performance. Follow instructions for lubricating and changing acc

6Familiarize yourself with the following safety notices used in this manual: This means that if precautions are not heeded, it may result in minor

75.0 Glossary Arbor: Metal shaft that connects the drive mechanism to the blade. Bevel Edge Cut: Tilt of the saw arbor and blade between 0° and 45

86.0 Specifications Model number .......

9 Dust collection: Dust port outside diameter .........................